Preparation from scratch
Preparation from scratch

MBX®
Pneumatic HD

Verwijdert moeiteloos roest, lak, onderlagen, afdichtingsmiddelen van autopanelen.

MBX® PNEUMATIC HEAVY DUTY

De MBX® – de éénstapsgereedschap die gemakkelijk roest, corrosie, oxidatie, kleefmiddelen, pakkingen, laklagen, onderlagen , afdichtingsmiddelen, vinyl verwijdert en lasnaden netjes maakt. De flexibele draadbanden roteren in een gepatenteerde

behuizing, roteren met centrifugale kracht naar buiten en werken op een kussen van lucht. Speciaal ontworpen U-vormige borsteldraden, gemonteerd in een duurzame nylon borstelband, zorgen voor veilige, langdurige prestaties.

Verwijdert snel corrosie en oxidatie – zowel hard als zacht materiaal

Presteert op ongelijkmatige oppervlakken

Zeer flexibel in krappe ruimtes

Geen verstoppingen of het vastplakken van de borsteldraden. 

Reinigt oppervlakken gelijkmatig

Volledig zicht op het werkoppervlak

Specifications

Technical Datasheet

MB-001 coarse 23mm
STAAL, GROF. 23 MM.

Coating verwijderen

Technisch Gegevensblad

MB-020 coarse 11mm
STAAL, GROF. 11 MM.

Coating verwijderen

Technisch Gegevensblad

MB-009 medium 23mm
STAAL, MEDIUM. 23 MM.

Ontroesten

Technisch Gegevensblad

MB-021 medium 11mmDEZE
STAAL, MEDIUM. 11 MM.

Ontroesten

Technisch Gegevensblad

MB-005 fine 23mm
STAAL, FIJN. 23 MM.

Reinigen

Technisch Gegevensblad

MB-028 fine 11mm
STAAL, FIJN. 11 MM.

Reinigen 

Technisch Gegevensblad

MB-011 stainless coarse 23mm
ROESTVRIJ STAAL, GROF. 23 MM.

Aluminium

Technisch Gegevensblad

MB-011 stainless coarse 23mm
ROESTVRIJ STAAL, GROF. 11 MM.

Aluminium

Technisch Gegevensblad

MB-007 stainless fine 23mm
ROESTVRIJ STAAL, FIJN. 23 MM.

Aluminium

Technisch Gegevensblad

MB-028 fine 11mm
ROESTVRIJ STAAL, FIJN. 11 MM.

Aluminium

Technisch Gegevensblad

ZU-010-01d
Vinyl Zapper®

Decal power

Meer info:

ACCESSOIRES 

AS-009a
ADAPTERSYSTEEM 23 mm

AS-009

Specificaties

AS-012b
ADAPTERSYSTEEM  11 mm

AS-012

Specificaties

ZU-071 quadrat
LUCHTDRUKREGELAAR 23 MM

ZU-071

Specificaties (NPT)

Specificaties

LUCHTDRUKREGELAAR 11 MM

ZU-070

Specificaties (NPT)

Specificaties

ZU-020_Dust Exhaust for MBX® Pneumatic_RGB_72dpi
STOFUITLAAT

ZU-020

Specificaties

ZU-003_Re-sharpening Stone_MBX® Belts coarse and medium_RGB_72dpi
NASLIJPGEREEDSCHAP
VOOR borstelbandEN GROF EN MEDIUM

ZU-003

ZU-073b
DRAAIBARE CONNECTOR

ZU-073

Specificaties

Sets

SE-206-BMC case
MBX® Pneumatic Heavy Duty set
ZU-010-01d

De MBX® Pneumatic Heavy Duty set bevat de Vinyl Zapper®

De MBX® Pneumatic Heavy Duty is ook los verkrijgbaar (zonder de extra borstelbanden en koffer)

VEELGESTELDE VRAGEN

MBX®

What applications is the MBX® suitable for?

The MBX® Technology has been developed for preparing the surface of bodywork panels.

A selection of different MBX® Belts is available that are suitable for specific types of work:

  • MBX® Belt coarse, black: Underseal removal
  • MBX® Belt medium, ocher: Rust removal
  • MBX® Belt fine, green: Paint removal

Also available are blue MBX® Belts with stainless steel bristles, which are ideal for preparing body parts made of stainless steel, aluminum or other nonferrous metals.

Note: The MBX® is generally unsuitable for preparing surfaces other than those of vehicle body parts. The surfaces of steel structures are best prepared using the Bristle Blaster®.

What results does the MBX® Technology deliver?

The MBX® Technology is suitable for cleaning, that is, for removing coatings, rust and paint from car body panels. On such substrates, MBX® Belts – depending on the type of belt – also create a finish similar to that achieved with sandblasting (MBX® Belts coarse and medium).

However, the MBX® Technology is not suitable for preparing steel surfaces, especially when surface cleanliness (e.g. Sa 2½) and roughness specifications have to be met. The Bristle Blaster® should be used for such applications.

Can I also use MBX® Belts with other drive units?

No! MBX® Belts are specially designed for use with the MBX® drive units. These drive units run at the recommended optimum speed required by the MBX® Belts.

Working at the right speed (idling speed of MBX® Pneumatic = 3,500 rpm, MBX® Electric = 3,200 rpm) guarantees the best results and maximum lifetime for the belts.

What’s more, the in-line design of the MBX® drive units ensures optimum handling and control.

Can a MBX® drive unit also be used with Bristle Blaster® or Die Blaster® Belts?

No! The MBX® drive units are only suitable for use with MBX® Belts.

The design and functionality of Bristle Blaster® and Die Blaster® Belts differ fundamentally from those of MBX® Belts: They are designed to be operated in conjunction with an Accelerator Bar.

As a result, all three types of belt (MBX®, Bristle Blaster® and Die Blaster® Belts) can only be used together with the matching drive unit.

What servicing work does the MBX® need?

Pneumatic

The compressed-air motor should be regularly oiled. All you have to do is put a few drops of low-viscosity oil into the compressed-air connection. Proper maintenance ensures that the tool enjoys a longer service life and is a precondition for warranty claims.

Electric

Clean the motor housing every time after using the tool and, in particular, blow out the fan with compressed air to remove any dust.

You can find instructions on how to replace the carbon brushes in the user manual in the section headed Maintenance. All repairs should be carried out only by specialists trained in the repair of power tools or by other appropriately qualified tool servicing staff.

Where can I find instructions on how to use the MBX®?

It is crucial that you use the MBX® correctly, so that you obtain the results that you want. You can find appropriate instructions in the user manual enclosed with every set. We also recommend that you watch our application film.